Ultra-start 72 Series Bedienungsanleitung

REV.2007.11.14ATM72 SERIES Advanced Remote Starters &Vehicle Security SystemsINSTALLATION GUIDETMFCC ID NOTICEThis device complies with Part 15 of

SYSTEM PROGRAMMING - Menu 1PAGE 10INSTALL MANUAL SYSTEM WIRING DETAILS72 SERIESPIN 1PIN 1YELLOWBLACKPIN 2PIN 2GREENWHITEPIN 3REDPIN 4REDPIN 5BLUEPIN

SYSTEM PROGRAMMING - Menu 1PAGE 11INSTALL MANUAL SYSTEM WIRING DETAILSWHITESYSTEM GROUND INPUTJUMPER SELECTABLE PARK LIGHT OUTPUT (+ OR -)BLACKBLUEO

9 PIN CONNECTORSYSTEM PROGRAMMING - Menu 1PAGE 12INSTALL MANUAL SYSTEM WIRING DETAILSPINKBRAKE SWITCH INPUT (+) WHEN BRAKE IS PRESSEDGREEN/WHITEHO

SYSTEM PROGRAMMING - Menu 1PAGE 13INSTALL MANUAL SYSTEM WIRING DETAILS72 SERIESPIN 1YELLOWPIN 2BROWNPIN 3BLACKPIN 4PIN 7RED /WHITEGRN/WHITEPIN 5PIN 8W

1- WHITE/VIOLET Wire- Ground When Running (-)Connect this wire to the your bypass modules negative turn on wire. When the remote starter is activated

SYSTEM PROGRAMMING - Menu 1PAGE 15INSTALL MANUAL PROGRAM MODEPress LockPress UnlockPress StartPress #MENU 1 MENU 2 MENU 3 MENU 41 - Cycle the Ignitio

SETS OPTION 1 – AUTO-LOCK & UNLOCK ENABLED- The doors will lock when the key is turned on and unlock the when the key is turned off.SETS OPTION 2

SYSTEM PROGRAMMING - Menu 1SYSTEM PROGRAMMING - Menu 1PAGE 17INSTALL MANUAL PROGRAM MODESETS OPTION 1 - SHORT PULSES- The output for lock and unlock

SYSTEM PROGRAMMING - Menu 1PAGE 18INSTALL MANUAL PROGRAM MODE1 CHIRP1 CHIRP2 CHIRPSCHANGE SETTING 1 - GOTO SETTING 2 - PRESS & RELEASE THE VALET

SYSTEM PROGRAMMING - Menu 1PAGE 19INSTALL MANUAL PROGRAM MODESYSTEM PROGRAMMING - Menu 1ENTERING PROGRAM MODE 372 SERIES1 CHIRPCHANGE SETTING 1 - G

SYSTEM PROGRAMMING - Menu 1PAGE 2INSTALL MANUAL TABLE OF CONTENTSQUICK VIEW WIRING DIAGRAM...3

SYSTEM PROGRAMMING - Menu 1PAGE 20INSTALL MANUAL PROGRAM MODECON'T FROM PREVIOUS PAGECHANGE SETTING 4 - GOTO SETTING 5 - PRESS & RELEASE TH

SYSTEM PROGRAMMING - Menu 1PAGE 21INSTALL MANUAL PROGRAM MODEENTERING PROGRAM MODE 472 SERIES1 CHIRPCHANGE SETTING 1 - GOTO SETTING 2 - PRESS & R

TACH / TACHLESS & HYBRID MODESSYSTEM PROGRAMMING - Menu 1PAGE 22INSTALL MANUAL PROGRAM MODE72 SERIESSETTING 1HYBRID VEHICLE 1Connect the Tach wi

SYSTEM PROGRAMMING - Menu 1PAGE 23INSTALL MANUAL TRANSMITTER PROGRAMMINGSYSTEM PROGRAMMING - Menu 1ENTERING REMOTE PROGRAM MODEThe system can lean up

DOOR LOCK DIAGRAMSGreenVehicle's Lock/Unlock SwitchTo Control Relay orActuatorsNEGATIVE DOOR LOCK (LOW CURRENT)Alarm and / or StarterModuleDoor l

SYSTEM PROGRAMMING - Menu 1PAGE 25INSTALL MANUAL RELAY DIAGRAMSVehicle's Lock/Unlock SwitchUSE SPDT 12v RelayNEGATIVE ONE WIRE DOOR LOCKSGroundG

SYSTEM PROGRAMMING - Menu 1PAGE 26INSTALL MANUALDIAGNOSTICS DIAGNOSTICS CHART TO ENTER DIAGNOSTIC MEMORYIf the remote starter does not activate when

SYSTEM PROGRAMMING - Menu 1PAGE 27INSTALL MANUAL NOTES72 SERIES

**FOR DETAILED VEHICLE WIRING INFORMATION GO TO:http://www.ultrastarters.com/wiring_diagrams.htmlThis site is for registered and authorized dealer onl

(+) GLOW PLUG - PROGRAMMABLE/ - SEE PAGE 13(+) START TRIGGERSYSTEM PROGRAMMING - Menu 1PAGE 372 SERIESINSTALL MANUAL QUICK VIEW WIRE DIAGRAM153246123

SYSTEM PROGRAMMING - Menu 1PAGE 4INSTALL MANUAL QUICK VIEW WIRE DIAGRAM1231231234Position 1 or Position 2GREEN BLUEN/A*REDBLACKWHT/VIOLETBYPASS MODU

SYSTEM PROGRAMMING - Menu 1PAGE 5INSTALL MANUAL QUICK VIEW PROGRAMMINGPress LockPress UnlockPress StartPress #MENU 1 MENU 2 MENU 3 MENU 41 - Cycle the

SYSTEM PROGRAMMING - Menu 1PAGE 6INSTALL MANUAL QUICK VIEW PROGRAMMING72 SERIESPROGRAM MODE 1SETTING #LEDFLASHESWIRE COLORSETTINGDESCRIPTIONOPTION 1

2NDIGNITIONSETTING #LEDFLASHESWIRE COLORSETTINGDESCRIPTIONOPTION 11 CHIRPOPTION 22 CHIRPSOPTION 33 CHIRPS1 WHITE(6 PIN CONNECTOR)2BLUE & GREEN(DOO

SYSTEM PROGRAMMING - Menu 1PAGE 8INSTALL MANUAL TACH / TACHLESS LEARNING AUTO TACH/ TACHLESS LEARNINGHorn will chip to confirm that the Tach/ Tachle

SYSTEM PROGRAMMING - Menu 1PAGE 9INSTALL MANUAL TACH / TACHLESS LEARNING* If the vehicle does not have a starter wire a manual tach learn must be p