Ultra-start 25XX Series Bedienungsanleitung

Covers All 25xx and 26xx Series Remote Starter/ Alarms-The system must be placed into Service Mode before any service work is started on the vehicle.

Step 1 - Connect All Of the Following Wires6 Pin Power ConnectorYellow 30amp Starter Output 12volts during start position only.Green 30amp Heater Outp

Manual Transmission “M” ModelsNever install an automatic transmission remote starter into a manualtransmission vehicle!!! Doing so may result in serio

Auto Tach Learn1) Turn the ignition key to the “ON” position. (The park lights will turn on*).2) Start the vehicle with the key, The LEDs on the anten

Important Tach NotesTach Learning the remote starter is one of the most important steps in the installationprocess. Do not tach learn vehicle while th

Entering Program Mode1) With the ignition in the OFF position, turn the ignition key from “Off” to “On” 3 times,ON-OFF-ON-OFF-ON within three seconds.

Quick View Programming* See the following pages for more detailed programming instructions.Menu 1 - Press Lock 1 Flash 2 Flashes 3 Flashes1 Ignit

Menu 1- User SettingsIgnition ON-OFF-ON-OFF-ONPress & Release Program ButtonPress Lock ButtonSetting 1 Ignition Auto Lock1) Ignition Lock & Un

Menu 1- User Settings...continued from previous pageSetting 5 Active/Passive Locks1) No Auto-Lock with Passive Arm 1 Flash/Chirp No auto-lock with pas

*(Default Settings)Menu 2 - Additional SettingsIgnition ON-OFF-ON-OFF-ONPress & Release Program ButtonPress Unlock ButtonSetting 1 Secure Valet Mo

Page 19Menu 3- Starter SettingsIgnition ON-OFF-ON-OFF-ONPress & Release Program ButtonPress Button #3Setting 1 Special Door Lock/Unlock Operations

Table of ContentsINSTALLATION MANUALREMOTE VEHICLE STARTER/ALARMPage 2Pre-Installation Page 3ComponentsFeature ListPre-InstallationInstallation Proced

Menu 4- Tach SettingsSetting 1 Auto Tach Learn.1) Perform a System Reset. See page 15.2) Turn the ignition key on. (Park lights will turn on).3) Start

Page 21REMOTE VEHICLE STARTER/ALARM INSTALLATION MANUALStep 1 - Within 3 seconds turn the ignition ON-OFF-ON-OFF-ON - LeavingKey ONStep 2 - Press and

87868587a3087868587a30LockUnlockVehicleLock/UnlockSwitchTo Control Relayor ActuatorGreenFused +12VBlueGroundNegative Type Door Locks 250maNegative Doo

87868587a3087868587a30BlueGreenLockUnlockVehicleLock/UnlockSwitchToActuatorFused +12VxxCutCut87868587a30GroundDIAGNOSTICS1387868587a3087868587a30BlueG

DIAGNOSTICSIf the remote starter does not activate when the start button is pressed the park lightswill flash a diagnostic to indicate what shutdown i

Recommended Pre-Installation ProceduresFeature List- Control module - 2 4 button transmitters*- Antenna with built in - 6 pin main harness with dual-

Recommended Installation ProceduresUnder Hood Connections - Route the hood pin and tach wire through the firewallinto the engine compartment. If possi

REMOTE VEHICLE STARTER/ALARM INSTALLATION MANUALPage 5Wiring Diagram135246214365781010109121211111413134PINBLUE30 AMP STARTER DISABLE RELAY- NORMALLY

Page 6INSTALLATION MANUAL REMOTE VEHICLE STARTER/ALARMSide ViewPIN4REDPN4IWEHIT4PINWHITEPN3IWHITENote-250ma outputs are low current and are designed t

Page 7REMOTE VEHICLE STARTER/ALARM INSTALLATION MANUAL6-pin Description Test For Wire1-Yellow 30amp Starter Output This wire will test 0volts in off

Page 8INSTALLATION MANUAL REMOTE VEHICLE STARTER/ALARM14 Pin ConnectorContinued From Previous Page1-Green Door Lock Door Lock Output - Programmable M

Page 9REMOTE VEHICLE STARTER/ALARM INSTALLATION MANUAL6 Pin Power ConnectorStep1-Connect All Of the Following WiresYellow 30amp Starter Output 12volts